Tag:Magnetic steel

  • 20mn23alv continuous casting and grinding casting

    Time:2021-3-2

    The non-magnetic steel 20mn23alv used to be mainly ground cast, but now continuous casting is the mainstream.20mn23alv high manganese non-magnetic steel has very low permeability and good mechanical properties and processing properties, which is used in the manufacture of non-magnetic parts in electrical equipment such as transformers, magnetic separators and motors.Due to the high alloy […]

  • Non magnetic reinforced screw plate

    Time:2021-2-22

    Where on earth will non-magnetic reinforcement, non-magnetic thread and non-magnetic steel plate be used?And why do these places use nonmagnetic materials?Concealed works, special infrastructure, wharf. Non magnetic steel is commonly used in these places.In addition, degaussing treatment should be carried out frequently at the ship terminal.These places must be low magnetized, if not low magnetized, […]

  • 40mn18cr3 motor damping slot wedge

    Time:2021-2-16

    Non magnetic steel 40mn18cr3 forging finger is a key component of turbo generator, which can strengthen and support the silicon steel sheet of rotor. It bears the hot fitting stress and centrifugal force produced by high speed rotationHigh high low magnetic structural steel.Therefore, higher mechanical properties, especially higher yield strength, are requiredIn order to prevent […]

  • 40mn18cr4v flat rolling

    Time:2021-2-7

    With the rapid development of electronic industry and magnetic material industry, there is an increasing demand for high strength non-magnetic steel. Usually, austenitic stainless steel is used to make dies, but the hardness and strength of austenitic stainless steel are low, and the service life of dies is very short. So we choose better high […]

  • 50mn18cr4 retaining ring

    Time:2021-2-5

    The static recrystallization of 50mn18cr4 non-magnetic steel for retaining ring can strengthen the properties of the steelIt can be used as motor retaining ring, high wear-resistant non-magnetic bearing and non-magnetic parts in various precision instrumentsThe experimental results show that the steel in use in our country can obtain relatively fine and uniform structure after cold […]

  • 45mn17al3 low magnetic steel

    Time:2021-1-10

    45mn17al3 low magnetic steel is also called 917 high alloy single phase austenite low magnetic manganese steel. It has good plasticity, high toughness, high work hardening tendency, high thermal expansion coefficient, high resistivity, low thermal conductivity and low magnetic properties. It is widely used in non-magnetic building, non-magnetic machinery, mineral processing and prospecting equipment, military […]

  • 45mn17al3 non magnetic steel

    Time:2021-1-3

    917 low magnetic steel 45mn17al3 has developed 917 low magnetic thin plate, low magnetic thick plate, low magnetic flat steel, low magnetic round steel and 45mn17al3 non-magnetic ball flat steel in some buildings or equipment requiring degaussing function in recent years. Gao GaoSpherical flat steel is a kind of medium profile which is mainly used […]

  • Cold cutting blanking of 40mn18cr4 non magnetic steel

    Time:2020-12-18

    We don’t understand other non-magnetic steel. High manganese non-magnetic steel series of 40mn18cr3, 40mn18cr4v, 50mn18cr5, 45mn17al3 and other steel grades are mainly used for degaussing steel of motor parts.Many friends reported that it was difficult to cut high manganese steel, and some said it was particularly difficult.Recently, a friend reported that cutting 40mn18cr4v non-magnetic round […]

  • Non magnetic reinforced ribbed steel plate

    Time:2020-12-3

    Where on earth will use non-magnetic reinforcement, non-magnetic thread, non-magnetic steel plate?And why are nonmagnetic materials used in these places?Concealed works, special infrastructure, wharf. Non magnetic steel is commonly used in these places.Degaussing treatment should be carried out on the site frequently.These places must be low magnetized, if not, the value of the surrounding magnetic […]

  • 40mn18cr4v flattening

    Time:2020-11-25

    With the rapid development of electronic industry and magnetic material industry, the demand for high-strength non-magnetic steel is increasing day by day. Generally, austenitic stainless steel is used to make dies, but the hardness and strength of austenitic stainless steel are low, and the service life of the die is very short. Therefore, we choose […]

  • 45mn17al3 low magnetic section steel

    Time:2020-10-17

    The main factor of permeability property of 45mn17al3 steel. The reasonable chemical composition, heat treatment process and surface processing requirements of sample are determined by industrial testThe test results show that the relative permeability μ r of 45mn17al3 steel is less than or equal to 1.005 at 800, 4 000 and 8 000 a / […]

  • X40mncr18 non magnetic steel

    Time:2020-8-27

    X40mncr182 stainless steel, German non-magnetic steel grade.Chemical composition: x40mncr182Carbon C: 0.30 ~ 0.4Silicon Si: 0.30 ~ 0.80Mn: 17.00 ~ 19.00Phosphorus P: ≤ 0.100Sulfur s: ≤ 0.050Cr: 1.50 ~ 5.00German standard non magnetic steel set:X120Mn13、DIN1.3802 ,X35Mn18、DIN1.3805,X40MnCrN19 、DIN1.3813,X40MnCr18 2、DIN1.3815,X40MnCr18 23 、DIN1.3816,X40MnCr18、DIN1.3817,X50MnCrV20 14、DIN1.3819,X4CrNi18 18 13、 DIN1.3941,X5MnCr18 13、DIN1.3949,X4CrNiMoN18 14、DIN1.3853 … . National standard non magnetic steel:40mn18cr3, 40mn18cr4, 40mn18cr4v, 45mn17al3, […]